+1 973 536 2331

sales@yusaki.jp

Enotec KES 132.1 (120480) in JAPAN

Get the best sales prices in JAPAN for Enotec KES 132.1 (120480) from Yusaki LLC.

Product: KES 132.1 (120480)

Brand: Enotec

Country: Japan

Description: Heater

Techical specification: (Sondenheizung 115 V)

Condition: New (Unused)

Yusaki LLC is here to help you with procurement of KES 132.1 (120480) Heater and other products and spare parts of Enotec.

Get help from our experts for sales prices for products of Enotec - KES 132.1 (120480) Heater in Japan.By buying products of Enotec and using our service you get high quality products with cheap prices.Our services will save you time and money which on the other side will help you growth your business!We're not an official distributor of Enotec, yet we are importing it on reasonable prices.Source the best sales prices for Enotec - KES 132.1 (120480) Heater in Japan.During the past years we managed to develop enough to satisfy the requirements of our customers.Contact us by e-mail or just fill out our RFQ form online.

Our company is not an authorized distributor or representative for this brand. We are a reseller company for this brand.

Other products from Enotec

AQUATEC 1000 ,ORDER NO. 20533-111291 ,PROBE TYPE : SME- 53200K10 PROBE SER NO: 11118392KF ELECTRONIC SERIAL NO: 020411 PROBE TUBE NO: 10.0793H&A PROBE CELL NO: 110418808MLT

ECO-00200000 Optional OXITEC Econom~ 02-Grenzwerte: OXITEC Economy 2x O.. Grenzwerte

ECO-1100105E OXITEC Economy: Elektronik mit 50m Kabel Sonde mit SintermetaU-Filterkopf

FEP-0002 pneumatic cable

FEP-0009 Cable to connect the probe to ATEX electronic device

FEP-0009-CG2 2 pcs. ATEX EExd IIC cable glands for FEP-0009 3/4'' NPT

KES - 132000S Sensor to measure oxygen MLT protection

KES-10004000 Filterkopf Economy mit Sintermetallfilter

KES-10000000 (OXITEC Economy InSitu-O2-Sonde, Mat.: 1.4301/1.4571, Flansch: DN65 PN6)

KES-10003000 OXITEC Economy Sintermetall-Filterkopf L = 500 mm Der Filterkopf besteht aus korrosionsbeständigem Edelstahl 1.4571 (316ss) und besitzt einen Sintermetallfilter. Die Basissonde besitzt einen Filterkopf mit eine Länge von ca. 500 mm, wodurch die Messsonde diese Eintauchtiefe erreicht. Größere Eintauchtiefen werden durch entsprechend längere Filterköpfe erreicht. Der Filterkopf sitzt im Rauchgaskanal an der Sondenspitze über dem ZrO2-Sensor. Es handelt sich hierbei um einen Diffusionsfilter, der auch bei hohen Staubbeladungen nicht verschmutzt. Zur Überprüfung der Messgenauigkeit und bei Kalibrierung des OXITEC-O2-Analysensystemes wird mit Luft oder einem beliebigen anderen Prüfgas, mit bekannter O2-Konzentration, das Filtervolumen gespült und Prüfgas statt Rauchgas wird gemessen.

KES-132090 KES-1321 Keramik-Filterkopf mit Flammensperre und V-Schild

KES-1321000 Replacement complete probe model 132.1 but without filter head and calibration gas valvelength: 385 mm

KEX-50011115A0 Measurement probe , model 5001 KEX , with filter head blowout and sintered metal filter INCOLOY (2.4816) ATEX II 2G Ex d IIC T3 Gb Cooling pipe Protec (SiSiC) 1000 mm Gas temperature : up to 1400 ° C, Probe length 464 mm. Measuring principle : cell with zirconia The flue gas pressure : -50 to +50 mbar Flow rate: 0 to 50 m / s Ambient temperature : -40 ° C to +80 ° C Response time : 0,5 s ( at a speed > 10 m / s) Time T90: 5 s ( at a speed of > 10 m / s) Material probe : V4A (SS316Ti) Degree of protection ( junction box ): IP 65 Lower limit of detection: less than 1 ppm O2 Power supply: from the electronic device Manual valve supply standard gas Safety distance tube Mounting flange ANSI 4 "

OXITEC 5000 ECO OKSİJEN ANALİZÖR CİHAZI

OXITEC 5000 PLU-0025 29329372 Original Spare Part

O2-Sonde KES-5002; Nr. KES-500200000

SIK-132X SIK-132x Replacement inner probe assembly consisting of: Heater element, Ceramic Heater Support, Thermocouple, Ceramic rod, Signal wire, Ref. air tube, clips and fittings fully tested and assembled ready to slide in to the terminal box end o the probe. Note: the oxygen cell does NOT need removal!

SME-5D2F0030 Electronic device SME 5 in two buildings ATEX II 2G Ex d IIC T6 Gb, IP 66 Power Supply : 230V/50 Hz, ± 10% Pneumatic device EExd systems Sheet steel housing IP 65 with flowmeter reference and calibration gas manual power calibration gas instrumentation air ( provided by customer ) Measuring ranges : programmable from ppm to 100 % O2 Accuracy : ± 0.2% of reading Ambient temperature : -20 ° to +55 ° C Analog Output: programmable 0/4-20 mA, 500 P Temperature compensation : e Calibration in a single section with distance , or at two points with air and span gas or two points with standard gas

ZO2-0001FOR MODEL KES132X SENSOR

Yusaki LLC

584-0023 2-2-16 Wakamatsuchohigashi, Tondabayashi City, Osaka Prefecture

Phone:
+81 721-26-8450

Fax:
+81 721-26-7242

E-mail:
sales@yusaki.jp

| |